Altera EPM3512A overview
Altera EPM3512A MAX 3000A Series Programmable Logic Devices High–performance, low–cost CMOS EEPROM–based programmable logic devices (PLDs) built on a MAX�...
Product details
Manufactured byAltera
Product groupCPLD Devices
DescriptionAltera EPM3512A MAX 3000A Series Programmable Logic Devices
Key FeaturesHigh–performance, low–cost CMOS EEPROM–based programmable logic devices (PLDs) built on a MAX® architecture (see Table 1) 3.3-V in-system programmability (ISP) through the built–in IEEE Std. 1149.1 Joint Test Action Group (JTAG) interface with advanced pin-locking capability – ISP circuitry compliant with IEEE Std. 1532 Built–in boundary-scan test (BST) circuitry compliant with IEEE Std. 1149.1-1990 Enhanced ISP features:– Enhanced ISP algorithm for faster programming– ISP_Done bit to ensure complete programming– Pull-up resistor on I/O pins during in–system programming High–density PLDs ranging from 600 to 10,000 usable gates 4.5–ns pin–to–pin logic delays with counter frequencies of up to 227.3 MHz MultiVoltTM I/O interface enabling the device core to run at 3.3 V, while I/O pins are compatible with 5.0–V, 3.3–V, and 2.5–V logic levels Pin counts ranging from 44 to 256 in a variety of thin quad flat pack (TQFP), plastic quad flat pack (PQFP), plastic J–lead chip carrier (PLCC), and FineLine BGATM packages Hot–socketing support Programmable interconnect array (PIA) continuous routing structure for fast, predictable performance Industrial temperature range PCI compatible Bus–friendly architecture including programmable slew–rate control Open–drain output option Programmable macrocell flipflops with individual clear, preset, clock, and clock enable controls Programmable power–saving mode for a power reduction of over 50% in each macrocell Configurable expander product–term distribution, allowing up to 32 product terms per macrocell Programmable security bit for protection of proprietary designs Enhanced architectural features, including:– 6 or 10 pin– or logic–driven output enable signals– Two global clock signals with optional inversion– Enhanced interconnect resources for improved routability– Programmable output slew–rate control Software design support and automatic place–and–route provided by Altera’s development systems for Windows–based PCs and Sun SPARCstations, and HP 9000 Series 700/800 workstations Additional design entry and simulation support provided by EDIF 2 0 0 and 3 0 0 netlist files, library of parameterized modules (LPM), Verilog HDL, VHDL, and other interfaces to popular EDA tools from third–party manufacturers such as Cadence, Exemplar Logic, Mentor Graphics, OrCAD, Synopsys, Synplicity, and VeriBest Programming support with the Altera master programming unit (MPU), MasterBlasterTM communications cable, ByteBlasterMVTM parallel port download cable, BitBlasterTM serial download cable as well as programming hardware from third–party manufacturers and any in–circuit tester that supports JamTM Standard Test and Programming Language (STAPL) Files (.jam), Jam STAPL Byte-Code Files (.jbc), or Serial Vector Format Files (.svf)
General DescriptionMAX 3000A devices are low–cost, high–performance devices based on the Altera MAX architecture. Fabricated with advanced CMOS technology, the EEPROM–based MAX 3000A devices operate with a 3.3-V supply voltage and provide 600 to 10,000 usable gates, ISP, pin-to-pin delays as fast as 4.5 ns, and counter speeds of up to 227.3 MHz. MAX 3000A devices in the –4, –5, –6, –7, and –10 speed grades are compatible with the timing requirements of the PCI Special Interest Group (PCI SIG) PCI Local Bus Specification, Revision 2.2.
Manufacturer, product group, and supply
See who makes this product, where it belongs, and where available inventory may be listed.
Manufactured by
Altera
View Altera profile
Available from
Sourcing support available
Start a sourcing request